If you’re in the industrial, construction, or machinery repair space, you know that a loose fastener is one of the easiest ways to end up with a failed assembly — and a lock washer is the unsung hero of keeping bolts and nuts secured under vibration, temperature shifts, or heavy loads. As a washer supplier who’s worked with thousands of technicians, engineers, and maintenance teams over the past 12 years, I’ve seen too many people install lock washers wrong, and watch those mistakes lead to costly downtime or even safety hazards. This post isn’t just a step-by-step guide; it’s the practical, on-the-job knowledge I’ve picked out over years of talking to folks who actually use these parts every day. I’m not here to throw industry jargon at you — just the stuff that works, and how to make sure your lock washer does its job right, no matter what project you’re tackling. Washers

First, let’s cut through the confusion: not all lock washers are made the same, and using the wrong type is half the battle. I’ve had customers call me after a job where their spring lock washers bent, or their tooth lock washers just spun instead of gripping — almost always because they grabbed the first part off the shelf without checking if it fit their bolt size and application. There are two main types you’ll deal with regularly, and each has a specific use case, so it’s worth knowing the difference.
Spring lock washers, the ones with a split helix shape, are the most common for general-purpose use. They work by creating a spring-like load between the fastener head or nut and the joint surface, so when vibration tries to loosen the bolt, the washer’s tension pushes back, keeping the nut tight. They’re cheap, easy to stock, and perfect for automotive repairs, light machinery, or construction fixtures where you need a reliable, low-cost option. But they’re not for high-load or permanent assemblies — their helix can flatten over time if the joint puts constant pressure on them, which is why I always advise customers to switch to tooth lock washers for heavy-duty work.
Tooth lock washers, also called external or internal tooth lock washers, have small, sharp teeth around their edge, and their whole job is to dig into both the fastener’s bearing surface and the joint material (metal, wood, or even concrete) to create a mechanical lock. This is the type you want for equipment like conveyor belts, agricultural machinery, or structural steel assemblies where vibration is extreme. External tooth washers grip the joint side, while internal ones grip the fastener side — I usually tell folks to go with external if the joint material is soft (like aluminum or wood) because they dig in without damaging the surface, and internal if the fastener head is soft (like stainless steel) to avoid scratching it. One quick note here: never use a tooth washer on a joint where the surface is extremely smooth, like polished stainless steel — the teeth won’t grip, so it’s just a flat spacer, and you’re wasting your time.
Now, even if you have the right washer, installing it wrong will render it useless, and I’ve seen every mistake there is. Let’s break down the step-by-step process, with the pitfalls I see every time, so you don’t make them.
The first step is the easiest, but it’s where most people skip a check: match the washer size to the bolt. This is non-negotiable. A #10 lock washer won’t fit a 5/16 bolt, and a metric M8 washer is too small for a M10 bolt. I keep a size chart taped to my warehouse wall, and I make sure every customer who orders from me gets a printed copy too — if your washer’s inner diameter is too small, it won’t fit over the bolt, and if it’s too big, it will spin around, negating any locking power. Even a 1/32 difference in diameter can make a huge impact, so measure twice before you grab the part. If you’re working with imperial fasteners, the inner diameter of the washer should be 1/32 inch larger than the bolt shank; for metric, it should be 0.5 mm larger. That tiny gap ensures the washer sits flush against the bolt’s shoulder, not the threads, which is key for even tension.
Next, prepare the joint and the fastener surfaces. This is something most people overlook, but a dirty joint will keep a lock washer from doing its job. If the surface has oil, grease, rust, or paint, the washer won’t grip as intended — the tension from a spring washer will be reduced, and the teeth on a tooth washer will slide instead of digging in. Before you install, wipe the area with a clean rag, and if it’s rusty, use a wire brush to scrub away loose rust. For painted surfaces, sand a 1-inch area around the bolt hole to bare metal if you’re using a tooth washer — the teeth need a solid surface to bite into. Also, make sure the bolt hole is clean: if there’s burrs or metal shavings around the hole, they can make the washer sit unevenly, which will cause the fastener to tilt and loosen over time.
Now, place the lock washer correctly on the bolt. Here’s the rule I never deviate from: the split (for spring lock washers) or the teeth (for tooth lock washers) should face away from the fastener. Wait, let me say that again: it’s a small detail that makes all the difference. For spring lock washers, the open part of the split should point toward the direction the nut will turn when you tighten it. If the split faces the opposite way, the tension from the washer will be wasted — instead of pushing back against the nut’s loosening force, it will push sideways. For tooth lock washers, this is even more critical: external teeth face the joint (so they dig into the surface), internal teeth face the fastener. If you flip it, the teeth will be resting on smooth metal instead of gripping, and the fastener could scratch the joint’s surface. I’ve had a customer bring in a conveyor that kept loosening, and when we pulled it apart, the tooth washers were flipped — they had installed the internal teeth facing the steel frame, so they never bit in, and the machine’s constant vibration worked the nuts loose in two weeks. That’s a $1,000 repair that could have been avoided by flipping one washer 180 degrees.
Once the washer is in place, tighten the nut — but here’s another big mistake: overtightening, or under-tightening, the fastener. A lock washer relies on a specific amount of axial tension (the force pulling the joint together) to work. If you under-tighten, the washer’s tension won’t activate — it’s just a flat ring between the nut and joint, no locking power. If you overtighten, especially with a spring lock washer, you can flatten the helix permanently, so it can’t spring back when vibration hits. The right way to tighten is to use a torque wrench, if you have one, to match the manufacturer’s recommended torque for your bolt and washer. If you don’t have a torque wrench, use a standard wrench: tighten the nut until it’s snug, then give it an extra quarter-turn — that’s the sweet spot for most general applications. For tooth lock washers, once you feel the teeth grip, stop — don’t crank it tighter, or you’ll bend the teeth and ruin the lock.
Wait, one more step: never stack lock washers. I’ve seen this so many times — someone uses two spring lock washers to get more tension, or stacks a tooth washer on top of a spring washer. That’s a bad idea. Stacking washers distorts the load: the two washers will compress unevenly, so neither can do its job. If you need more tension, go with a thicker single washer, not two thin ones, or a spring washer designed for heavy loads. The only exception is if you’re using a lock washer with a flat washer — wait, no, actually, that’s a common practice, and it works when done right. Let’s clarify: if you’re using a lock washer, you usually don’t need a flat washer, but if the joint surface is soft (like wood or plastic), a flat washer under the lock washer will spread the load and prevent the lock washer from digging too deep and damaging the joint. That’s a separate step, not stacking. A flat washer goes under the lock washer, not between the lock washer and the nut — that way, the lock washer still does its job of locking, and the flat washer protects the surface.
Now, let’s talk about what not to do, because these are the mistakes that come up every single day. First, don’t use a lock washer as a spacer. That’s a waste of a perfectly good lock washer, and if you just need to fill a gap, use a flat washer — lock washers are designed to create tension or grip, not to add thickness. Second, don’t use lock washers in applications that require a permanent joint. If you’re bolting two steel beams together for a building that never moves, a lock washer is overkill — you’re better off with a bolt that’s installed with thread locker, since a lock washer will eventually lose tension under constant load. Third, don’t ignore material compatibility. If you’re using stainless steel bolts, don’t pair them with a zinc-plated steel lock washer — the two metals will corrode together (galvanic corrosion) over time, making the washer stick and lose its locking power. Always match the material: stainless steel with stainless steel, zinc-plated with zinc-plated, etc. I keep a stock of matched material washers so my customers don’t have to worry about that, because nothing kills a project like a corroded fastener two months after installation.
Let’s test this process with a real example, to make it concrete. Last month, a customer who runs a small farm brought me a batch of loose bolted connections on his hay baler — he’d been using cheap spring lock washers, and they were bending every 3 months, leading to downtime during harvest. We walked through the process together: we swapped his spring washers for external tooth lock washers (since balers have extreme vibration), matched each washer to the correct bolt size, sanded the rust off the steel frame around each hole, placed the external teeth facing the frame (joint side), tightened each nut to the correct torque, and skipped the flat washer because the frame was thick steel. He called me a week later to say the connections hadn’t loosened once, even after 12-hour days of baling. That’s exactly what this process is for — it’s not just theory, it’s solving real problems for real people.
Now, if you’re working on a project where safety is non-negotiable, like automotive brakes or structural rigging, there’s one extra tip: always inspect your lock washers before installation. Look for cracks, bent teeth, flattened helixes, or any wear — a damaged lock washer can’t do its job, even if you install it perfectly. I always include a quick inspection with every washer order I send out, because a split washer with a 1mm crack won’t provide the tension you need, and risking a loose bolt in a load-bearing assembly is never worth it.
At the end of the day, a lock washer is a small part, but getting it right saves you time, money, and headaches. I’ve been in the washer supply business for over a decade, and the number one piece of advice I can give anyone is to treat this part with as much care as you treat the bolt or nut you’re pairing it with. Skip the shortcuts, match the size and type to your application, and follow the steps we talked through.

If you’re working on a project and aren’t sure which lock washer is right for you, or you need a bulk order that’s sized and matched correctly, feel free to reach out to our team to discuss your needs. We can help you pick the right part for your job, no matter how big or small.
Switches References
- Machine Design. “Lock Washers: Types, Selection, and Installation Best Practices.” Penton Media, 2021.
- ASME B18.21.1. “Compression Type Lock Washers, Helical Spring and Tooth Lock Washers.” American Society of Mechanical Engineers, 2020.
- Fastener Technology International. “Galvanic Corrosion in Fastener Assemblies.” Fastener News Desk, 2019.
- Machinery’s Handbook, 31st Edition. “Locking Devices for Fasteners.” Industrial Press Inc., 2020.
Baoding Sihedan Electric Technology Co., Ltd.
Baoding Sihedan Electric Technology Co., Ltd. is well-known as one of the leading washers manufacturers and suppliers in China. Welcome to buy high quality washers at low price from our factory. Contact us for more discount information.
Address: No.68 Dongpingjie, Shijiazuo Village, Shenxing Town, Baoding City, China
E-mail: lucky@dkline.net
WebSite: https://www.dklinepower.com/